Doorgaan naar hoofdcontent

CreateLAB TQ5.2 zomaar een dagje...


Bruisende Energie en Innovatie in CreateLAB TQ5.2, Eindhoven!

In het creatieve hart van Fontys-ICT, gevestigd op TQ5.2 in Eindhoven, borrelde gisteren een zee van activiteit en innovatie in het CreateLAB. Het was een dynamische samenkomst van studenten en docenten, waarbij geluid en signaalverwerking niet alleen werden besproken maar ook live in actie kwamen!

Opvallend was dat bijna elke techniek-docent een bepaalde connectie met geluid bleek te hebben, aangezien velen een instrument bespeelden. Terwijl de melodieën door de ruimte zweefden, waren studenten parallel daaraan druk bezig met hun eigen lopende projecten.

Een highlight was ongetwijfeld de testrit met een zelfgebouwde robot, een project waar studenten diep in de ROS2-software duiken en zich richten op navigatie binnen bebouwde omgevingen. Met behulp van LIDAR-technologie ontwikkelen ze kaarten en werken ze aan een AGV (autonoom rijdend voertuig) dat pakketjes kan vervoeren binnen onze afdeling.

Neem een kijkje bij de bijgevoegde video en ervaar het perspectief van de robot terwijl deze door de gang navigeert - tot aan het moment waar de camera plotseling een onverwachte kennismaking met de vloer heeft... Er is altijd avontuur te beleven bij TQ5.2 CreateLAB!

Mis Onze Wekelijkse Live Video-Stream Niet!

Maar dat is niet alles! We hebben wekelijks een live video-stream op Twitch (twitch.tv/create_lab), waar we een kijkje geven in onze diverse avonturen en projecten. Iedereen is vrij om aan hun eigen projecten te werken en deze te demonstreren, en we nodigen je van harte uit om deel uit te maken van onze creatieve escapades, of je nu fysiek of virtueel bij ons bent. Doe mee, kijk mee, en ontdek samen met ons de wonderen van technische innovatie en creativiteit!

Reacties

Populaire posts van deze blog

Denon DHT T100 DESIGNED TO FAIL : bad caps (ceramic caps this time)

A friend gave me a Denon DHT-T100 to look at. Do not spend much time on it.. ok. It had a problem, it started clicking and ticking after power on, and after some time. (a so called intermittent problem) Sometimes it did not tick or click, but it was basically not usable. The clicking had a sharp click in one channel and repeated after about a second, then sound recovered and it would click and drop out again. He told me, do not spend any time on it, yeah, right. ;-) like I would give up after 15 minutes. I wanted to know what was going on with this thing, I found some schematic online and started measuring the usual things. The power supply, 24V did it drop down when a tick occurred ? Difficult to find out because sometimes the thing would play for hours without a glitch. I eventually found out the 24 V PSU, the step down SMPS on board and the LDO's were all ok, all power rails remained within spec, but it still glitched sometimes. (while power was ok) I investigat

Fixed voltage on cheap buck converter (MP1584) conversion with single 0805 resistor

Everywhere I look on the Ali and Ebays I see these step down converters based on MP1584. I bought a couple and actually they are not bad at all. The output voltage is set by the trimming-resistor in the left top corner of the picture. This works OK, but.. it is dangerous because it is rather sensitive to the touch. I decided that I wanted fixed output, so I had to figure out how this thing worked. The datasheet looks like this : R1 in the datasheet is what I call "R feedback" in my image. The value of R2 is mostly 8.2K Ohm in the boards I have seen.  So to set some common values for output voltage: change R1 to 27K for 3V3 output (actually 3.4 volt, but 27K is a standard value) or change R1 to 43K0 for 5.0 Volt output. (43 K is a standard value) A standard 0805 size resistor fits precisely, how convenient ;-). Make sure the other resistor is really 8.2K because that determines the feedback ratio. This way you can not burn up your circ

DPS5005 power supply, remote control using python serial port modbus

Just a short one. I bought one of these things. It can do 50 volt 5 Amp, I have not looked at the quality of the output (noise, overshoot all unknown to me)  but should be alright to control a lamp, a battery or a strip of LED's is my guess. You can easily control the current and voltage output using a serial port. (a usb-serial-rs485 was provided) I seems to talk modbus protocol. To change the baud rate and modbus-slave-address, keep POWER button pressed during power on, this will enter you into the configuration menu. register list here : Register Map for this device. Function Description Number of bytes Decimal places UNIT Read/Write Register address U-SET Voltage setting 2 2 V R/W 0000H I-SET Current setting 2 3 A R/W 0001H UOUT Output voltage display value 2 2 V R 0002H IOUT Output