Doorgaan naar hoofdcontent

Printplaat reparatie van : Brink Renovent HR uit 1997 met details en uitleg


Ik heb een nieuw filmpje gemaakt. 
Reparatie van printplaat van Brink Renovent HR uit 1997 met gedetailleerde uitleg en foto's.

Voor #BarryV van repareerjeventilatie.nl heb ik weer een printplaat gerepareerd. Het betrof een print van de Brink Renovent HR deze hebben als motor : EBM R1G140-AW05-12 en deze vind je regelmatig in WTW installaties die door Brink zijn geproduceerd.

Deze specifieke print had waterschade en hierdoor was bijna alles opgeblazen en kapot.
- CPU, motor drivers, FET eindtrappen, weerstanden en dioden, en een op-amp.

Ondanks dat is het toch weer gelukt om de print te repareren.

Het wordt steeds belangrijker om zorgvuldig met grondstoffen om te gaan, onderdelen en nieuwe producten hebben lange levertijden.

Reparatie en recycling is een goede optie, economisch en ecologisch en nu blijkt ook verstandig vanuit een geopolitiek perspectief, we zijn wel erg afhankelijk van een paar fabrieken geworden.

Leerzaam voor wie wat wil leren over reparatie van elektronica en globale opbouw van een motor stuurprint, of gewoon wat slimmer wil worden ;-)


Reacties

Unknown zei…
Hallo, ik heb hetzelfde apparaat, en had helaas een dubbele storing! Ten eerste had de EC-ventilator gefaald. Het bleek dat de Hall-sensor defect was. Ik heb dit vervangen, en de ventilator werkt weer op de printplaat, die nog steeds functioneel is! De eigen printplaat heeft het echter begeven, kennelijk in het microcontroller-gedeelte, dat speciaal geprogrammeerd is en dus volgens mij helaas niet vervangen kan worden! Ik zou een beetje technische discussie zeer op prijs stellen! Groeten uit Duitsland ;)
Dierki zei…
Moin.
Auch bei mir ist der Hallsensor defekt.
Welchen Sensor haben Sie eingebaut und wo haben Sie ihn gekauft.
Ich konnte bisher nicht den richtigen Sensor finden.
Danke schon mal für Ihre Hilfe.
#oetelx zei…
I could not find the original type.
I got another Hall sensor type with same pinout and it worked for me.
https://www.tinytronics.nl/shop/image/data/Producten/Componenten/Overige/a3144eul.pdf

The type is A3144 from Allegro.
A local shop had it in stock https://www.tinytronics.nl/shop/nl/sensoren/magnetisch-veld/3144-hall-effect-switch

Thanks for reading my blog and fixing the world one step at a time.

Populaire posts van deze blog

Denon DHT T100 DESIGNED TO FAIL : bad caps (ceramic caps this time)

A friend gave me a Denon DHT-T100 to look at. Do not spend much time on it.. ok. It had a problem, it started clicking and ticking after power on, and after some time. (a so called intermittent problem) Sometimes it did not tick or click, but it was basically not usable. The clicking had a sharp click in one channel and repeated after about a second, then sound recovered and it would click and drop out again. He told me, do not spend any time on it, yeah, right. ;-) like I would give up after 15 minutes. I wanted to know what was going on with this thing, I found some schematic online and started measuring the usual things. The power supply, 24V did it drop down when a tick occurred ? Difficult to find out because sometimes the thing would play for hours without a glitch. I eventually found out the 24 V PSU, the step down SMPS on board and the LDO's were all ok, all power rails remained within spec, but it still glitched sometimes. (while power was ok) I investigat

Fixed voltage on cheap buck converter (MP1584) conversion with single 0805 resistor

Everywhere I look on the Ali and Ebays I see these step down converters based on MP1584. I bought a couple and actually they are not bad at all. The output voltage is set by the trimming-resistor in the left top corner of the picture. This works OK, but.. it is dangerous because it is rather sensitive to the touch. I decided that I wanted fixed output, so I had to figure out how this thing worked. The datasheet looks like this : R1 in the datasheet is what I call "R feedback" in my image. The value of R2 is mostly 8.2K Ohm in the boards I have seen.  So to set some common values for output voltage: change R1 to 27K for 3V3 output (actually 3.4 volt, but 27K is a standard value) or change R1 to 43K0 for 5.0 Volt output. (43 K is a standard value) A standard 0805 size resistor fits precisely, how convenient ;-). Make sure the other resistor is really 8.2K because that determines the feedback ratio. This way you can not burn up your circ

DPS5005 power supply, remote control using python serial port modbus

Just a short one. I bought one of these things. It can do 50 volt 5 Amp, I have not looked at the quality of the output (noise, overshoot all unknown to me)  but should be alright to control a lamp, a battery or a strip of LED's is my guess. You can easily control the current and voltage output using a serial port. (a usb-serial-rs485 was provided) I seems to talk modbus protocol. To change the baud rate and modbus-slave-address, keep POWER button pressed during power on, this will enter you into the configuration menu. register list here : Register Map for this device. Function Description Number of bytes Decimal places UNIT Read/Write Register address U-SET Voltage setting 2 2 V R/W 0000H I-SET Current setting 2 3 A R/W 0001H UOUT Output voltage display value 2 2 V R 0002H IOUT Output